FilamentFix

FilamentFix

Diagnose. Dry. Store. Print.

VERIFIED FILAMENT LIBRARY · 26 VERIFIED / PARTIALLY VERIFIED ENTRIES

Manufacturer-first filament data with visible verification status.

Verified means the value shown is traceable to the linked manufacturer source. Needs verification means the manufacturer page used here does not publish that specific field, so FilamentFix leaves it open rather than borrowing a generic number.

26 entries shown
Manufacturer / productMaterialVerified dataDrying status
Bambu Lab PETG HFPETG HF65 °C · 8 h; <20% RH while printing/keepingVerified
Polymaker PETGPETG60 °C · 6 h if moisture absorbedVerified
Prusament PLA / rPLAPLA45 °C · 6 hVerified
Prusament WoodfillWood-filled PLA family45 °C · 6 hVerified
Prusament PVBPVB45 °C · 8 hVerified
Prusament PETGPETG55 °C · 6 hVerified
Prusament TPUTPU60 °C · 4–6 hVerified
Prusament PP CF/GFPP composite70 °C · 2–4 hVerified
Prusament ASAASA80 °C · 4 hVerified
Prusament PC BlendPC blend85 °C · 5 hVerified
Prusament PC Blend Carbon FiberPC-CF90 °C · 4 hVerified
Prusament PC Space GradePC90 °C · 4–6 hVerified
Prusament PA11 Carbon FiberPA11-CF90 °C · 6 hVerified
Prusament PEIPEI150 °C · 8 hVerified
BCN3D PLAPLAOfficial print profile + compatibility pageNeeds verification
BCN3D Tough PLATough PLAOfficial print profile + storage guidanceNeeds verification
BCN3D TPU 98ATPU220–245 °C nozzle; 45–60 °C bed; airtight storage + desiccantNeeds verification
BCN3D PET-GPET-G230–250 °C nozzle; airtight storage + desiccantNeeds verification
BCN3D PVAPVA210–230 °C nozzle; 45–60 °C bed; highly hygroscopicNeeds verification
BCN3D BVOHBVOH190–210 °C nozzle; 45–90 °C bedNeeds verification
BCN3D ABSABS230–250 °C nozzle; 95 °C bed; airtight storage + desiccantNeeds verification
BCN3D PPPP210–240 °C nozzle; 70 °C bedNeeds verification
BCN3D PAPA / Nylon220–250 °C nozzle; 95 °C bed; dry before printing recommendedDrying temp/time needs verification
BCN3D PAHT CF15PAHT-CF260–280 °C nozzle; 95 °C bed; Hotend X required; airtight storageNeeds verification
BCN3D PP GF30PP-GF230–250 °C nozzle; 80 °C bed; Hotend XNeeds verification
BCN3D PET CF15PET-CF245–265 °C nozzle; 95 °C bed; Hotend X; very low moisture absorptionNeeds verification

All entries checked September 13, 2026. A “Needs verification” drying field means the linked official page used for this entry did not state a drying temperature/time.

FILAMENT PASSPORTS

Exact product. Exact source. Visible verification status.

Filament passports keep print settings, drying, storage and documentation tied to the exact product that published them. Unknown values stay unknown instead of being filled with plausible-looking guesses.

Status key: Verified = traceable manufacturer source · Needs verification = a field is not confirmed by the source used · Conflict = credible sources for the same exact product disagree.

Bambu Lab PETG HF

MaterialPETG HF
Drying65 °C · 8 h, blast drying oven
Humidity<20% RH while printing / keeping, sealed with desiccant
Nozzle230–260 °C
Bed65–75 °C with glue
StatusVerified

Source checked Sep 13, 2026: Bambu Lab PETG HF.

Polymaker PETG

MaterialPETG
Drying60 °C · 6 h if material has absorbed moisture
Nozzle240–260 °C
Bed60–70 °C
Fan20–60%
StatusVerified

Source checked Sep 13, 2026: Polymaker PETG.

Prusament PETG

MaterialPETG — all versions in Prusa drying table
Drying55 °C · 6 h
StorageClosed storage with desiccant recommended in Prusa guidance
StatusVerified for drying scope shown

Source checked Sep 13, 2026: Prusa — Drying filament.

Prusament PLA / rPLA

MaterialPLA / rPLA
Drying45 °C · 6 h
USS Drybox referenceBelow 30% RH; short-term tolerance up to 40%
StatusVerified

Sources checked Sep 13, 2026: Prusa drying · Prusa USS Drybox.

BCN3D PET-G

MaterialPET-G
Nozzle230–250 °C
Bed60 °C enclosed models / 80 °C open models
Speed30 mm/s enclosed / 45 mm/s open
StorageAirtight container with desiccant when not in use
Drying valueNot stated on the BCN3D support page used for this passport
StatusVerified print/storage · Drying needs verification

Source checked Sep 13, 2026: BCN3D PET-G.